Southwest Ranches is one of South Florida's most distinctive communities: expansive estate lots, working equestrian facilities, luxury ranch-style homes, and the kind of roofing projects, in both scale and complexity, that have no equivalent in the urban core. A 7,000 sq ft estate roof with hip geometry, covered lanais, and a secondary standing-seam barn structure is a completely different undertaking than a typical suburban re-roof. This guide covers what Southwest Ranches property owners need to know about roofing their main residence and their agricultural structures, which contractors are qualified to take on the work, and why dual licensure (CGC1541144 and CCC1337790) matters more here than almost anywhere else in Broward County.
Robson Industrial Group LLC serves Southwest Ranches and all of Broward County as a Florida Certified General Contractor (CGC1541144) and Florida Certified Roofing Contractor (CCC1337790). We are also a GAF Certified™ Residential Roofing Contractor (GAF ID 1164276), authorized to offer the GAF System Plus Limited Warranty. One of the strongest manufacturer warranties available in the U.S. roofing market. Our qualifier, Francisco Rijo, holds all active licenses in good standing, verifiable at myfloridalicense.com.
Estate Home Roofing in Southwest Ranches: Scale, Complexity, and Why Licensed Matters More
When a homeowner in Miami Gardens or Miramar calls about a re-roof, the job is typically 1,400–2,000 sq ft of flat or low-slope surface with a handful of penetrations. When a Southwest Ranches estate owner calls, the conversation starts at a very different point. A 6,000 sq ft footprint with a hipped roof, two covered lanais, a detached garage structure, a cupola, dormers, and a mix of barrel tile and metal flashing is a project that can run $80,000–$150,000 and require coordination between a roofing crew, a structural engineer, a crane operator, and a tile supplier. That is not hyperbole: it is the reality of Southwest Ranches residential construction.
The license combination of CGC1541144 (Certified General Contractor) and CCC1337790 (Certified Roofing Contractor) is critical for estate-scale projects because roofing on a structure of this complexity involves structural decisions, not just surface decisions. Heavy concrete tile on large spans requires structural load analysis. Adding or modifying a covered lanai roof connection involves structural elements. Repairing rafter tails and exposed framing under a tile roof requires a licensed GC. A roofing contractor operating under CCC1337790 alone may not legally supervise structural work, and the Town of Southwest Ranches Building Department, supported by Broward County plan review, will flag unlicensed structural activity during inspections.
| Factor | Standard Suburban CBS (~1,800 sq ft) |
Southwest Ranches Estate (~6,000 sq ft) |
|---|---|---|
| Roof Area | ~2,200 sq ft installed | 7,500–12,000+ sq ft installed |
| Typical System | Shingle or low-slope modified bitumen | Barrel tile, standing seam metal, or concrete tile — sometimes combined |
| Roof Planes & Valleys | 2–4 planes, 0–2 valleys | 8–20+ planes, multiple complex valleys, dormers, and hip returns |
| Penetrations | 2–4 (HVAC, vents) | 10–30+ (multiple HVAC systems, skylights, chimney caps, exhaust fans, solar) |
| Project Cost Range | $12,000–$28,000 | $65,000–$175,000+ |
| Trades Involved | 1–2 (roofing + flashing) | 3–6 (roofing, structural, crane, tile, metal, HVAC coordination) |
| Permit Complexity | Standard roofing permit | Roofing permit + possible structural engineering stamp for lanai/dormer elements |
| Licenses Required | CCC1337790 (roofing) | CCC1337790 (roofing) + CGC1541144 (structural elements) |
What a Dual-Licensed Contractor Brings to an Estate Project
Holding both CGC1541144 and CCC1337790 is not a formality. It changes what we can legally do on your property. On a large estate re-roof, that might mean:
- Evaluating and repairing the existing roof deck structure before new tile or metal goes down
- Modifying rafter tail or fascia connections that have deteriorated behind the existing tile system
- Installing hurricane strapping between the roof structure and the wall framing — structural work that requires CGC1541144
- Coordinating with a structural engineer of record for permitted span modifications
- Pulling a single comprehensive permit that covers both the structural and roofing scopes, simplifying the inspection process for the Town of Southwest Ranches
Large Project Logistics on Southwest Ranches Properties
Southwest Ranches properties offer logistical advantages suburban jobs do not: large lots with room for dumpster placement, material staging areas away from the main residence, and easier crane access for heavy tile pallets or long standing-seam panels. We coordinate material delivery and staging to minimize disruption to equestrian areas. Horses are not moved during deliveries, and we communicate material drop schedules in advance. Robson Industrial Group LLC (CGC1541144 / CCC1337790) typically crews estate projects at 8–14 workers for peak installation days, enabling rapid enclosure of large roof areas before afternoon rainstorms during summer roofing season.
Equestrian Facility Roofing: Barns, Stables, Covered Arenas, and Agricultural Structures
Southwest Ranches is unique in Broward County for its concentration of active equestrian properties: horse stables, covered riding arenas, hay and feed storage barns, equipment sheds, and working ranch structures that need roofing attention just as much as the main residence. In fact, on many properties the agricultural structures represent more total roof area than the house itself, and they have been neglected longer. Many Southwest Ranches barn roofs are original 1970s and 1980s installations with exposed-fastener corrugated metal or aging wood framing that is significantly compromised after 40+ years of Florida humidity, UV exposure, and hurricane seasons.
Life-Safety Note: A barn roof failure during a hurricane is not merely a property loss event. It is a life-safety crisis for the animals inside. Horses cannot evacuate on their own. A stable roof that blows off during a Category 2 or 3 storm event means horses exposed to wind-driven rain, flying debris, and potential structural collapse. This is an urgency angle unique to equestrian properties, and it is why pre-season roof inspection and hardening is not optional on Southwest Ranches horse properties. Robson Industrial Group LLC (CCC1337790 / CGC1541144) performs pre-hurricane season evaluations and fastener/strap upgrades for agricultural roofing systems throughout Southwest Ranches.
| Structure Type | Typical Roof System | HVHZ Product Approval Req. (NOA / HVHZ-listed FL#) | Hurricane Tie-Down | Ventilation Req. | Maint. Schedule | Replacement Lifespan |
|---|---|---|---|---|---|---|
| Post-frame barn | Exposed-fastener metal (R-panel or AG panel) | Yes — all panels | Critical — hurricane straps at each post | Ridge vent or open ridge required | Annual gasket/fastener inspection | 20–35 years (exposed fastener) |
| 12-stall stable | Exposed-fastener or standing seam metal | Yes | Critical — animal occupancy; straps mandatory | Ridge ventilation essential for horse health | Semi-annual inspection | 25–50 years depending on system |
| Covered riding arena | Standing seam metal (large span) | Yes — span-specific | Critical — large roof surface, extreme wind load | Sidewall open or ridge/cupola required | Annual — focus on ridge and eave | 40–70 years (hidden fastener) |
| Hay / feed storage | Exposed-fastener metal (AG panel) | Yes | Standard — 6-foot strap intervals | Gable vents recommended | Annual gasket check | 20–30 years |
| Equipment barn / garage | Metal or shingle on wood frame | Yes | Standard | Gable or ridge vent | Annual | 20–30 years (shingle) / 35–50 (metal) |
Hurricane Strap and Fastener Requirements for Agricultural Construction
Post-frame agricultural construction is inherently less hurricane-resistant than CBS residential construction when not properly engineered. The connection between the roof diaphragm and the posts must be continuous and code-compliant. Florida Building Code requires hurricane straps or clips at every rafter-to-top-plate connection, and on post-frame structures the equivalent connection between the roof purlins and the structural posts must be appropriately rated for the design wind speed. 140 mph for interior Broward County. A contractor holding CGC1541144 (structural) and CCC1337790 (roofing) can evaluate and upgrade all of these connections in a single project scope, pulling one permit through the Town of Southwest Ranches.
Ventilation: Critical for Both Horse Health and Roof Longevity
An enclosed stable without adequate ridge ventilation runs dangerously hot in Florida summers. Dangerous for horses and destructive to the roof system itself. Trapped heat and moisture accelerate fastener corrosion, cause panel oil-canning, and promote mold in adjacent wood framing. On occupied stabling, we install full ridge ventilation (continuous ridge vent or open ridge with bird-screen) as a standard element of any stable re-roof or new installation. This is not optional: it protects your investment and your animals. Robson Industrial Group LLC holds CCC1337790 for the roofing system and CGC1541144 for any structural framing work at the ridge connection.
Exposed-Fastener vs. Hidden-Fastener Panels for Agricultural Use
Exposed-fastener panels (R-panel, corrugated) remain the most common choice for agricultural structures in Southwest Ranches: they are faster to install, more economical per square foot, and widely available in Broward County. Their limitation is the neoprene gasket at each screw penetration, which degrades under Florida UV within 8–15 years and requires periodic replacement to prevent water infiltration. Standing seam (hidden fastener) eliminates this maintenance point entirely, but costs 30–50% more to install. For a high-value barn adjacent to a luxury estate home where aesthetics and longevity matter, standing seam is increasingly the right choice. For a working hay storage or equipment barn, exposed-fastener R-panel is typically the practical and economical answer. Robson Industrial Group LLC (CCC1337790 / CGC1541144) installs and services both systems.
Standing Seam Metal Roofing: The Southwest Ranches Premium Choice
Standing seam metal roofing has become the prestige choice for Southwest Ranches estate homes, and for good reason: it delivers a 40–70 year lifespan, superior hurricane wind resistance, eliminates nearly all ongoing maintenance, and produces excellent drainage performance on the low-slope areas common in large ranch-style floor plans. For properties that combine a main residence with agricultural structures, standing seam can create a unified architectural aesthetic across all structures, something exposed-fastener corrugated metal cannot accomplish on the estate side of the property.
| System | Cost/Sq Ft Installed | Lifespan | Hurricane Performance | Estate Aesthetics | HOA Compat. | HVHZ Product Approval (NOA / HVHZ-listed FL#) | GAF System Plus (ID 1164276) |
|---|---|---|---|---|---|---|---|
| Exposed-fastener AG panel | $6–$10 | 20–35 yr | Good (gasket failure risk) | Agricultural only — not suitable for residence | Barn/ag only | Yes | Not typically applicable |
| Standing seam (concealed fastener) | $14–$22 | 40–70 yr | Excellent — no gaskets to fail | Excellent — clean modern/ranch aesthetic | Generally yes | Yes | Yes — qualifying GAF metal systems under GAF ID 1164276 |
| Stone-coated metal tile | $12–$18 | 40–50 yr | Very good | Excellent — mimics tile aesthetics | Yes — where tile look required | Yes | Check by specific product |
| Painted Galvalume standing seam | $15–$24 | 50–70 yr | Excellent | Premium — PVDF paint for fade resistance | Yes | Yes | Yes — qualifying systems under GAF ID 1164276 |
Gauge Selection: 24-Gauge vs. 26-Gauge for Broward County
For standing seam metal roofing in Broward County, which sits in the High-Velocity Hurricane Zone with design wind speeds of roughly 170 mph and up (ASCE 7 Risk Category II; parcel-specific per the FBC wind-speed map), 24-gauge steel is the recommended minimum for residential estate applications. 26-gauge is acceptable for agricultural structures and some lower-slope applications but offers less dent resistance and is more prone to oil-canning on wide panels. Robson Industrial Group LLC (CCC1337790 / CGC1541144) specifies 24-gauge as the standard for Southwest Ranches estate homes and installs 26-gauge on agricultural secondary structures where the cost efficiency is appropriate to the use.
PVDF Paint Systems and Florida UV Performance
South Florida UV degradation is relentless. A standing seam system installed with standard polyester paint will chalk and fade noticeably within 8–12 years. PVDF (polyvinylidene fluoride) paint systems, marketed under trade names like Kynar 500®, retain color integrity for 30–40 years in Florida sun exposure and carry written finish warranties from the steel manufacturer. For a Southwest Ranches estate home where a standing seam roof is a significant architectural statement, PVDF paint is not an upgrade. It is the correct specification. All Robson Industrial Group LLC (CGC1541144 / CCC1337790) standing seam installations on estate residences use FL Product Approval-rated panels with manufacturer-documented paint systems.
GAF Certified™ Coverage on Metal Roofing Systems
As a GAF Certified™ Residential Roofing Contractor (GAF ID 1164276), Robson Industrial Group LLC can offer the GAF System Plus Limited Warranty on qualifying roofing installations. GAF manufactures metal roofing products including the DecoTech® metal shingle system, which installs over a complete GAF waterproofing system and qualifies for the full System Plus warranty when installed by a GAF Certified Residential Roofing contractor. The GAF System Plus Limited Warranty provides enhanced non-prorated coverage on the GAF materials in the system; workmanship is covered separately by Robson's own written warranty, with the term stated in the contract: a documented pair that matters to estate homeowners who may own the property for decades. Ask about GAF Certified warranty documentation (GAF ID 1164276) for your specific project.
Combining Metal and Tile on Complex Estate Properties
Some Southwest Ranches estate homes feature a combination roofing approach: concrete or clay tile on the main residence for aesthetic continuity with the home's architecture, and standing seam metal on secondary structures, covered lanais, and outbuildings for low-maintenance performance. This is a legitimate and increasingly common design approach, but it requires a contractor who understands both systems at the flashing integration points, where the two systems meet at hips, valleys, or wall terminations. Robson Industrial Group LLC (CCC1337790 / CGC1541144) installs both systems and manages the integration details that determine whether a mixed-system roof performs well over the long term.
Hurricane Season Stakes for Southwest Ranches Properties
Many Southwest Ranches homeowners believe their inland location provides meaningful hurricane protection relative to coastal communities. This assumption deserves scrutiny. A Category 3 hurricane tracking through interior Broward County still delivers sustained winds at or above 111 mph, with gusts well above that threshold. Southwest Ranches is in the High-Velocity Hurricane Zone, because the Florida Building Code puts all of Broward County in it, and its design wind speeds run roughly 170 mph and up (ASCE 7 Risk Category II; the exact figure for a parcel comes from the FBC wind-speed map): not because the town is low-risk, but because the code requires all new construction to be engineered for that load. An older barn roof without hurricane straps, with corroded fasteners and degraded gaskets, is not engineered to withstand that wind. It will fail first.
| Property Type | Pre-Storm Steps | Vulnerable Points | Recommended Pre-Season Upgrades | Post-Storm Inspection |
|---|---|---|---|---|
| Estate home — tile roof | Inspect field tile + ridge cap attachment; verify underlayment integrity; clear gutters and drains | Ridge cap tiles; hip tiles; unsealed valleys; perimeter tile adhesion | Re-bond loose tiles with polyurethane foam; install SWR underlayment during next re-roof; verify hip/ridge cap count (CCC1337790) | Full aerial + ground tile count; underlayment exposure check; inspect all hip/ridge |
| Estate home — standing seam metal | Inspect seams and clip connections; verify all penetrations sealed; check eave fascia anchor | Endlap sealant; gutter attachment; penetration flashing | Re-seal any open endlaps or penetrations; verify seam continuity (CCC1337790 / CGC1541144) | Inspect all seams and panel ends; check ridge cap; verify fascia/gutter attachment |
| Post-frame barn | Inspect all exposed fasteners and gaskets; verify hurricane straps at each post; remove any loose debris stored in loft | Exposed fastener gaskets; ridge cap attachment; eave overhang; any unsealed gable end openings | Replace deteriorated gaskets (full re-fastening); install missing hurricane straps (CGC1541144); seal gable openings with rated panels | Count and inspect all fasteners for pull-through; check gable ends; inspect ridge and eave |
| Covered riding arena | Inspect large-span clip connections; verify ridge attachment; clear perimeter of debris; plan for animal shelter during storm | Eave overhang at perimeter (high uplift zone); clip engagement; sidewall openings | Upgrade to structural ridge clip; evaluate perimeter eave trim attachment; engineering review for large span (CGC1541144 / CCC1337790) | Full span inspection from underside; check all clip connections; inspect endwall trim |
The Economics of Pre-Season Hardening
A pre-hurricane season inspection and targeted hardening of an older barn roof (re-fastening corroded screws, replacing failed gaskets, installing missing hurricane straps) typically costs $3,000–$8,000 depending on the structure size. A post-storm emergency tear-off and replacement of the same roof, including debris removal, temporary tarp installation, and expedited contractor availability in the post-storm labor market, can easily run $35,000–$75,000 or more. The math is clear. Robson Industrial Group LLC (CCC1337790 / CGC1541144) performs pre-season agricultural roofing evaluations throughout Southwest Ranches and can prioritize inspection scheduling before the June 1 hurricane season start.
HVHZ Product Approval: All roofing panels installed by Robson Industrial Group LLC under license numbers CCC1337790 and CGC1541144 carry HVHZ approval (a Miami-Dade NOA or an FL Product Approval whose evaluation covers the HVHZ), which is what Broward County's wind design requirements call for. Never accept a contractor who cannot provide the NOA or HVHZ-listed FL approval for the specific panel or system they are installing on your property. This is a condition of the permit, not an optional quality upgrade.
The Permit Process: Town of Southwest Ranches Building Department
The Town of Southwest Ranches does not maintain an independent plan review staff at the scale of Miami-Dade or Fort Lauderdale. Instead, the Town issues permits through its Building Department at 13400 Griffin Rd, Southwest Ranches, FL 33330, reachable at (954) 434-0008, and routes plan review and inspections through Broward County Building Department. This two-step process means permit timelines can run somewhat longer than in municipalities with fully in-house review, and large or complex projects (such as a structural re-roof on a large barn with engineered span documentation) require a signed and sealed structural engineering drawing submitted to Broward County's reviewers before the permit is issued.
| Step | Who | What Happens | Typical Timeline |
|---|---|---|---|
| 1. Scope Definition | Contractor (CGC1541144 / CCC1337790) | Site visit; full roof assessment; scope of work documented; HVHZ product approvals (NOA or HVHZ-listed FL#) identified | Day 1–3 |
| 2. Application Submitted | Licensed contractor | Permit application, contract, product approvals, proof of license (CGC1541144 / CCC1337790), Workers' Comp certificate submitted to Town | Day 3–5 |
| 3. Broward County Plan Review | Town → Broward County Building | Plans reviewed for FBC compliance; structural engineering required for large agricultural spans | 5–15 business days |
| 4. Permit Issued | Town of Southwest Ranches | Permit posted at job site; work may begin | Upon plan approval |
| 5. Installation | Robson Industrial Group LLC (CCC1337790 / CGC1541144) | Roofing installation per approved plans; HVHZ-approved materials (NOA or HVHZ-listed FL#); GAF Certified™ installation protocols where applicable (GAF ID 1164276) | 5–14 days depending on scope |
| 6. Inspections | Broward County inspector (via Town) | Required inspections at deck stage and final; structural inspections if structural scope included | 1–3 days per inspection |
| 7. Final / CO | Town of Southwest Ranches | Final inspection pass; permit closed; wind mitigation inspection can now be completed by certified inspector | Day 1–3 after final inspection |
Why Barn Permits Are Not Optional
Agricultural structures in Southwest Ranches are permitted buildings, and re-roofing them without a permit is a code violation. Beyond the legal exposure, an unpermitted barn re-roof cannot be covered by your property insurer in the event of a claim, and will create problems when you sell the property. A contractor who suggests skipping the permit to save time or money is not acting in your interest. Robson Industrial Group LLC (CGC1541144 / CCC1337790) pulls all required permits for every project, residential or agricultural, in Southwest Ranches and throughout Broward County.
Insurance Premium Savings After Re-Roofing
Estate properties in inland Broward County carry substantial homeowners insurance premiums, particularly those insured through Citizens Property Insurance or surplus-lines carriers. A new roof documented with a wind mitigation inspection can generate $3,000–$8,000 per year in premium savings on large estate homes, depending on the prior roof age, the new system's wind rating, and the specific carrier. Concrete tile and standing seam metal both produce excellent wind mitigation credits when installed by a licensed contractor (CCC1337790 / CGC1541144) using FL Product Approval-rated materials with secondary water resistance underlayment. After your project closes, Robson Industrial Group LLC will connect you with a certified wind mitigation inspector to document your installation for your insurance carrier.
GAF System Plus Warranty Documentation
The GAF System Plus Limited Warranty (available through GAF Certified contractors, GAF ID 1164276) creates a documented trail of installation quality that is increasingly valued by estate homeowners who purchase properties with existing roof systems. When you sell a Southwest Ranches estate home, transferring a GAF System Plus warranty to the buyer is a meaningful differentiator. Warranty documentation, contractor certification records, and FL Product Approval numbers are maintained in your project file by Robson Industrial Group LLC.
Choosing the Right Contractor for Estate and Equestrian Properties
Southwest Ranches property owners are, by definition, high-net-worth individuals who have not reached their position in life by making uninformed decisions. The roofing contractor who shows up with a Craigslist advertisement and a handshake quote is not who you want on your estate property, and not who most Southwest Ranches owners would accept. This section covers what to look for and what to verify before signing a contract.
License Verification — Always Do This First
Florida contractor licenses are publicly searchable at myfloridalicense.com. Before signing any roofing contract for a Southwest Ranches property, verify that the contracting entity holds an active Florida Certified Roofing Contractor license (CCC prefix) and, for any structural work, an active Florida Certified General Contractor license (CGC prefix). Robson Industrial Group LLC holds both: CGC1541144 and CCC1337790, both active and in good standing, with Francisco Rijo as the qualifier of record. Do not rely on a contractor's verbal representation of their license status. Verify it yourself online.
License verification: CGC1541144 and CCC1337790 are both verifiable at myfloridalicense.com. GAF Certified™ contractor status (GAF ID 1164276) is verifiable at GAF's contractor locator. Always verify before signing: your property and your insurance coverage depend on it.
Experience with Large-Format and Agricultural Projects
Ask any prospective contractor for references on estate-scale projects (5,000+ sq ft roof area) and agricultural roofing projects (barns, stables, arenas) in Broward County. A contractor whose typical project is a 1,800 sq ft CBS shingle re-roof has no frame of reference for the logistics, crew management, and technical decisions involved in a $100,000 estate roof or a 12-stall stable replacement. Robson Industrial Group LLC (CGC1541144 / CCC1337790) has completed large-format residential and agricultural roofing projects throughout Broward County, and we can provide property-specific references upon request.
Workers' Compensation and Liability Insurance
At estate property values in Southwest Ranches (typically $800,000 to $3,000,000+) a contractor who does not carry active Workers' Compensation insurance is an unacceptable risk. If an uninsured worker is injured on your property, your homeowner's policy is the backstop. Request current Certificates of Insurance (COI) for both general liability and Workers' Compensation before work begins. Robson Industrial Group LLC (CCC1337790 / CGC1541144) carries full coverage and provides COIs upon request as a standard part of contract execution.
Timeline Expectations on Large Estate Roofs
A small suburban re-roof closes in 1–2 days. A Southwest Ranches estate roof project of 8,000–12,000 sq ft with tile or standing seam metal runs 8–14 production days, not including permit lead time. Set realistic expectations: a properly permitted, large-format re-roof in Southwest Ranches with licensed contractors (CGC1541144 / CCC1337790) and quality materials takes the time it takes. Contractors who promise dramatically faster timelines are either understating the scope or planning to under-crew the job.
Active Equestrian Properties: Special Considerations
Roofing an active horse property requires crew awareness of animal safety, dust and debris containment, and schedule coordination around feeding and turnout times. Robson Industrial Group LLC communicates work schedules to equestrian property owners in advance, stages materials away from paddock areas, and contains debris with tarps and collection systems that prevent nails and fasteners from reaching equestrian areas. If work is occurring adjacent to stabling, we coordinate with you to ensure horses are in appropriate areas during high-activity periods.
Frequently Asked Questions: Southwest Ranches Roofing
Yes. Any roofing work on a structure in Southwest Ranches (including barns, horse stables, covered arenas, and agricultural buildings) requires a permit issued through the Town of Southwest Ranches Building Department (13400 Griffin Rd, (954) 434-0008), with plan review handled by Broward County. Large agricultural spans may also require a signed and sealed structural engineering drawing. The licensed contractor submitting for the permit must hold a valid Florida Certified Roofing Contractor license (CCC1337790) and, for any structural elements, a Florida Certified General Contractor license (CGC1541144). Robson Industrial Group LLC holds both licenses and handles the full permitting process for Southwest Ranches clients.
Both tile and standing seam metal are excellent choices for Southwest Ranches estate homes, and the right answer depends on the home's architectural style, budget, and priorities. Concrete or clay tile delivers a classic Mediterranean or ranch aesthetic, exceptional longevity (50+ years), and outstanding fire resistance. Standing seam metal (concealed fastener) offers a 40–70 year lifespan, superior hurricane performance, lighter weight (important on large roof spans), and zero re-coating or gasket maintenance. For equestrian and agricultural secondary structures, exposed-fastener metal panels are the standard. Though hidden-fastener standing seam is increasingly chosen for high-end barn designs. Robson Industrial Group LLC (CCC1337790, CGC1541144, GAF Certified™ Residential Roofing Contractor, GAF ID 1164276) installs all major systems and can evaluate your specific estate layout.
Yes. GAF manufactures metal roofing products including qualifying metal systems, and GAF Certified™ contractors (GAF ID 1164276) can offer enhanced warranty coverage on qualifying GAF metal roofing installations. The GAF System Plus Limited Warranty provides non-prorated coverage for wind damage and manufacturing defects when a complete qualifying system is installed by a certified contractor. Robson Industrial Group LLC is a GAF Certified™ Residential Roofing Contractor (GAF ID 1164276) and can confirm which specific metal products and system configurations qualify for System Plus coverage on your Southwest Ranches property.
For large estate homes in inland Broward County, a new roof combined with a wind mitigation inspection can reduce homeowners insurance premiums by $3,000–$8,000 per year depending on the prior roof age, the new roofing system's wind rating, and the insurer. Citizens Insurance, common on high-value Broward properties, offers significant discounts for newer roofs and documented wind mitigation features such as secondary water resistance (SWR) underlayment, hip roof geometry, and enhanced fastening patterns. A licensed roofing contractor holding both CCC1337790 and CGC1541144 ensures that all installation details are done correctly and documentable for the wind mitigation inspector. Ask Robson Industrial Group LLC about scheduling a wind mitigation inspection following your reroofing project.
It depends on the scope of work. Replacing the roofing system on an existing agricultural structure with the same footprint and structural system can be completed under a Florida Certified Roofing Contractor license (CCC1337790) alone. However, if the project involves any structural modifications (adding a ridge beam, enlarging span, installing hurricane straps connected to structural elements, repairing or replacing post-frame members, or building a new structure) a Florida Certified General Contractor license (CGC1541144) is required for those elements. Robson Industrial Group LLC holds both CCC1337790 and CGC1541144, meaning we can legally and correctly handle the full scope of a barn re-roof regardless of whether structural work is involved, and we pull all required permits through the Town of Southwest Ranches.
Ready to Talk About Your Southwest Ranches Roofing Project?
Estate home, barn, stable, covered arena, or all of the above. Robson Industrial Group LLC is the dual-licensed contractor Southwest Ranches property owners trust. We pull the permits, install with licensed crews, and back every project with GAF Certified™ warranty documentation.
Robson Industrial Group LLC • 7290 NW 7th St, Unit 105, Miami, FL 33126 • sales@robsonindustrial.com
Licenses verifiable at myfloridalicense.com: CGC1541144 • CCC1337790